xDuoo XD-05 Plus USB Driver 4.6.7/ USB Firmware/XMOS Driver V4.13.0

Home Forums Firmware Download xDuoo XD-05 Plus USB Driver 4.6.7/ USB Firmware/XMOS Driver V4.13.0

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #523
    xDuoo OfficialxDuoo Official
    Senior Moderator

    Download xDuoo XD-05 Plus USB Driver 4.67.0/Firmware/ XMOS Drvier V4.13.0 

    Installation USB Driver on computer

    1).For Windows computer, NEED to install the USB driver, but please note that this driver is designed for Windows 7, Windows 8 and Windows 10 only, not suitable to use in Windows XP system.

    For MAC computer, NO NEED to install USB driver, only need to set up the output,  you can find the set up steps in the following ( Part Two).

    2). Before you install this USB driver, please check the SN number on the back of XD05 plus,

    If the SN number of your XD05 Plus IS between “03500100001—03500604654”, you will NEED to install the “XMO-Driver-v4.13.0” and update the firmware.

    If the SN number of your XD05 Plus IS NOT between “03500100001—03500604654”, there is NOT necessary to install “XMO-Driver-v4.13.0”, just continue here directly.

     

    Part One (This part is for Windows, steps by steps on how to install the USB Driver)

    If your computer is Mac, please jump to Part Two directly.

     

    How to install the the USB driver on Windows ?

    1. Double-click the file of xDuoo_UsbAudio_v4.67.0

    2. Click Next

    3. Click Next

    4. Click “install”

    5. After the installation, click “NEXT”

    6. Then click “FINISH”

    7. Click PC start menu, select: control panel – > hardware and sound – > hardware and sound – > sound, after a computer is ejected from an interface, click < play > option, and then select <xDuoo USB Audio> to set it as the default playback device.

    8. Finished, Play music on the PC, and enjoy yourself.

     

    Part Two ( This is for Mac Computer, NO NEED to install the USB driver)

     

    MAC computer audio output settings guide

    Note: MAC computer does not need to install USB driver, only need to set up the output

    1. Click the settings icon in the lower right corner of the computer pop-up interface, click the Voice icon (after connected the USB port of unit)

    2. Then in the pop-up interface, click the output, select xDuoo USB Audio 2.0 as the output device

    3. After setting is finished, there will be USB audio output through the unit.

    Note: Sometimes the MAC system setting the sampling rate of the device to 768KHZ, then will cause your DAC have no sound (if the DAC does not support 768KHZ sampling rate), then you need to set the output sampling rate in the audio MIDI settings, as shown below.

     

    Part Three ( This is for updating the firmware)

     

    Firmware update steps 

    If the SN number of your XD05 Plus IS between “03500100001—03500604654”, you will NEED to install the “XMO-Driver-v4.13.0” first and update the firmware.

    If the SN number of your XD05 Plus IS NOT between “03500100001—03500604654”, there is NOT necessary to install “XMO-Driver-v4.13.0” and update the firmware.

     

    1. Double-click the file of XMO-Driver-v4.13.0(No need install if you have install this driver before )

    2. Click “Next”

    3. Click “Next”

    4. Click “Install”

    5. After the installation, click “Next”

    6. Then click “Finish”

    7. Then, start to upgrading now

    Note: During the updating, please make sure there is enough power, and don’t turn off the device

    1) Turn on the unit, set it to “USB IN”, connect USB to computer.

    2. Open the C disk, find the folder” C:\Program files\XMOS\USBAudioStDriver_3085/W7,8,10_x64”

    3. Double-Click the” xmosusbaudiost3085_dfuapp”, click” Browse”, Load the firmware corresponding to your device

    4.  Click “Start”

    Finished!

    8. After update finished, uninstall the driver v4.13.0, then start installing the driver V4.67

Viewing 1 post (of 1 total)
  • You must be logged in to reply to this topic.